The effects of initial soil moisture conditions on swale flow hydrographs          下载免费PDF全文

Hendrik Rujner  Günther Leonhardt  Jiri Marsalek  Anna‐Maria Perttu  Maria Viklander 《水文研究》2018,32(5):644-654

The effects of soil water content (SWC) on the formation of run‐off in grass swales draining into a storm sewer system were studied in two 30‐m test swales with trapezoidal cross sections. Swale 1 was built in a loamy fine‐sand soil, on a slope of 1.5%, and Swale 2 was built in a sandy loam soil, on a slope of 0.7%. In experimental runs, the swales were irrigated with 2 flow rates reproducing run‐off from block rainfalls with intensities approximately corresponding to 2‐month and 3‐year events. Run‐off experiments were conducted for initial SWC (SWC_ini) ranging from 0.18 to 0.43 m³/m³. For low SWC_ini, the run‐off volume was greatly reduced by up to 82%, but at high SWC_ini, the volume reduction was as low as 15%. The relative swale flow volume reductions decreased with increasing SWC_ini and, for the conditions studied, indicated a transition of the dominating swale functions from run‐off dissipation to conveyance. Run‐off flow peaks were reduced proportionally to the flow volume reductions, in the range from 4% to 55%. The swale outflow hydrograph lag times varied from 5 to 15 min, with the high values corresponding to low SWC_ini. Analysis of swale inflow/outflow hydrographs for high SWC_ini allowed estimations of the saturated hydraulic conductivities as 3.27 and 4.84 cm/hr in Swales 1 and 2, respectively. Such estimates differed from averages (N = 9) of double‐ring infiltrometer measurements (9.41 and 1.78 cm/hr). Irregularities in swale bottom slopes created bottom surface depression storage of 0.35 and 0.61 m³ for Swales 1 and 2, respectively, and functioned similarly as check berms contributing to run‐off attenuation. The experimental findings offer implications for drainage swale planning and design: (a) SWC_ini strongly affect swale functioning in run‐off dissipation and conveyance during the early phase of run‐off, which is particularly important for design storms and their antecedent moisture conditions, and (b) concerning the longevity of swale operation, Swale 1 remains fully functional even after almost 60 years of operation, as judged from its attractive appearance, good infiltration rates (3.27 cm/hr), and high flow capacity.  相似文献   

The effects of floods on the temperature of riparian groundwater          下载免费PDF全文

Jeffery A. Watson  M. Bayani Cardenas  Stephen B. Ferencz  Peter S.K. Knappett  Bethany T. Neilson 《水文研究》2018,32(9):1267-1281

The transition area between rivers and their adjacent riparian aquifers, which may comprise the hyporheic zone, hosts important biochemical reactions, which control water quality. The rates of these reactions and metabolic processes are temperature dependent. Yet the thermal dynamics of riparian aquifers, especially during flooding and dynamic groundwater flow conditions, has seldom been studied. Thus, we investigated heat transport in riparian aquifers during 3 flood events of different magnitudes at 2 sites along the same river. River and riparian aquifer temperature and water‐level data along the Lower Colorado River in Central Texas, USA, were monitored across 2‐dimensional vertical sections perpendicular to the bank. At the downstream site, preflood temperature penetration distance into the bank suggested that advective heat transport from lateral hyporheic exchange of river water into the riparian aquifer was occurring during relatively steady low‐flow river conditions. Although a small (20‐cm stage increase) dam‐controlled flood pulse had no observable influence on groundwater temperature, larger floods (40‐cm and >3‐m stage increases) caused lateral movement of distinct heat plumes away from the river during flood stage, which then retreated back towards the river after flood recession. These plumes result from advective heat transport caused by flood waters being forced into the riparian aquifer. These flood‐induced temperature responses were controlled by the size of the flood, river water temperature during the flood, and local factors at the study sites, such as topography and local ambient water table configuration. For the intermediate and large floods, the thermal disturbance in the riparian aquifer lasted days after flood waters receded. Large floods therefore have impacts on the temperature regime of riparian aquifers lasting long beyond the flood's timescale. These persistent thermal disturbances may have a significant impact on biochemical reaction rates, nutrient cycling, and ecological niches in the river corridor.  相似文献   

Wetland hydroperiod classification in the western prairies using multitemporal synthetic aperture radar          下载免费PDF全文

Joshua S. Montgomery  Chris Hopkinson  Brian Brisco  Shane Patterson  Stewart B. Rood 《水文研究》2018,32(10):1476-1490

Wetlands represent one of the world's most biodiverse and threatened ecosystem types and were diminished globally by about two‐thirds in the 20th century. There is continuing decline in wetland quantity and function due to infilling and other human activities. In addition, with climate change, warmer temperatures and changes in precipitation and evapotranspiration are reducing wetland surface and groundwater supplies, further altering wetland hydrology and vegetation. There is a need to automate inventory and monitoring of wetlands, and as a study system, we investigated the Shepard Slough wetlands complex, which includes numerous wetlands in urban, suburban, and agricultural zones in the prairie pothole region of southern Alberta, Canada. Here, wetlands are generally confined to depressions in the undulating terrain, challenging wetlands inventory and monitoring. This study applied threshold and frequency analysis routines for high‐resolution, single‐polarization (HH) RADARSAT‐2, synthetic aperture radar mapping. This enabled a growing season surface water extent hyroperiod‐based wetland classification, which can support water and wetland resource monitoring. This 3‐year study demonstrated synthetic aperture radar‐derived multitemporal open‐water masks provided an effective index of wetland permanence class, with overall accuracies of 89% to 95% compared with optical validation data, and RMSE between 0.2 and 0.7 m between model and field validation data. This allowed for characterizing the distribution and dynamics of 4 marsh wetlands hydroperiod classes, temporary, seasonal, semipermanent, and permanent, and mapping of the sequential vegetation bands that included emergent, obligate wetland, facultative wetland, and upland plant communities. Hydroperiod variation and surface water extent were found to be influenced by short‐term rainfall events in both wet and dry years. Seasonal hydroperiods in wetlands were particularly variable if there was a decrease in the temporary or semipermanent hydroperiod classes. In years with extreme rain events, the temporary wetlands especially increased relative to longer lasting wetlands (84% in 2015 with significant rainfall events, compared with 42% otherwise).  相似文献   

Continuous real‐time analysis of the isotopic composition of precipitation during tropical rain events: Insights into tropical convection          下载免费PDF全文

Shaoneng He  Nathalie F. Goodkin  Dominik Jackisch  Maria Rosabelle Ong  Dhrubajyoti Samanta 《水文研究》2018,32(11):1531-1545

To investigate stable isotopic variability of precipitation in Singapore, we continuously analysed the δ‐value of individual rain events from November 2014 to August 2017 using an online system composed of a diffusion sampler coupled to Cavity Ring‐Down Spectrometer. Over this period, the average value (δ¹⁸O_Avg), the lowest value (δ¹⁸O_Low), and the initial value (δ¹⁸O_Init) varied significantly, ranging from ?0.45 to ?15.54‰, ?0.9 to ?17.65‰, and 0 to ?13.13‰, respectively. All 3 values share similar variability, and events with low δ¹⁸O_Low and δ¹⁸O_Avg values have low δ¹⁸O_Init value. Individual events have limited intraevent variability in δ‐value (Δδ) with the majority having a Δδ below 4‰. Correlation of δ¹⁸O_Low and δ¹⁸O_Avg with δ¹⁸O_Init is much higher than that with Δδ, suggesting that convective activities prior to events have more control over δ‐value than on‐site convective activities. The d‐excess of events also varies considerably in response to the seasonal variation in moisture sources. A 2‐month running mean analysis of δ¹⁸O reveals clear seasonal and interannual variability. Seasonal variability is associated with the meridional movement of the Intertropical Convergence Zone and evolution of the Asian monsoon. El Niño–Southern Oscillation is a likely driver of interannual variability. During 2015–2016, the strongest El Niño year in recorded history, the majority of events have a δ¹⁸O value higher than the weighted average δ¹⁸O of daily precipitation. δ¹⁸O shows a positive correlation with outgoing longwave radiation in the western Pacific and the Asian monsoon region, and also with Oceanic Niño Index. During El Niño, the convection centre shifts eastward to the central/eastern Pacific, weakening convective activities in Southeast Asia. Our study shows that precipitation δ‐value contains information about El Niño–Southern Oscillation and the Intertropical Convergence Zone, which has a significant implication for the interpretation of water isotope data and understanding of hydrological processes in tropical regions.  相似文献   

Moment Magnitude and Its Calculation     

Chen Yuntai  Liu Ruifeng 《中国地震研究》2018,32(4):447-455

In this paper, we give a brief introduction to the proposal and development history of the earthquake magnitude concept. Moment magnitude M_W is the best physical quantity for measuring earthquakes. Compared with other magnitude scales used traditionally, moment magnitude is not saturated for all earthquakes, regardless of big and small earthquakes, deep and shallow earthquakes, far field and near field seismic data, geodetic and geological data, moment magnitude can be measured, and can be connected with well-known magnitude scales such as surface wave magnitude M_S. Moment magnitude is a uniform magnitude scale, which is suitable for statistics with wide magnitude range. Moment magnitude is the preferred magnitude selected by the International Seismological community, and it is preferred by the departments responsible for publishing seismic information to the public.Moment magnitude is a uniform magnitude scale, which is suitable for statistics with wide magnitude range. Moment magnitude is a preferred magnitude for international seismology, it is preferred by the agency responsible for providing information about earthquakes to the public. We provide all formulas used in the calculation of moment magnitude, and the calculation steps in detail. We also analyzed some problems and rules to solve these problems by using different formulas and numerical value calculation steps.  相似文献   

Permanent earthquake‐induced actions in buried pipelines: Numerical modeling and experimental verification     

《地震工程与结构动力学》2018,47(4):966-987

Buried pipelines are often constructed in seismic and other geohazard areas, where severe ground deformations may induce severe strains in the pipeline. Calculation of those strains is essential for assessing pipeline integrity, and therefore, the development of efficient models accounting for soil‐pipe interaction is required. The present paper is aiming at developing efficient tools for calculating ground‐induced deformation on buried pipelines, often triggered by earthquake action, in the form of fault rupture, liquefaction‐induced lateral spreading, soil subsidence, or landslide. Soil‐pipe interaction is investigated by using advanced numerical tools, which employ solid elements for the soil, shell elements for the pipe, and account for soil‐pipe interaction, supported by large‐scale experiments. Soil‐pipe interaction in axial and transverse directions is evaluated first, using results from special‐purpose experiments and finite element simulations. The comparison between experimental and numerical results offers valuable information on key material parameters, necessary for accurate simulation of soil‐pipe interaction. Furthermore, reference is made to relevant provisions of design recommendations. Using the finite element models, calibrated from these experiments, pipeline performance at seismic‐fault crossings is analyzed, emphasizing on soil‐pipe interaction effects in the axial direction. The second part refers to full‐scale experiments, performed on a unique testing device. These experiments are modeled with the finite element tools to verify their efficiency in simulating soil‐pipe response under landslide or strike‐slip fault movement. The large‐scale experimental results compare very well with the numerical predictions, verifying the capability of the finite element models for accurate prediction of pipeline response under permanent earthquake‐induced ground deformations.  相似文献   

Bacteria‐sediment associations in an alpine,freshwater environment and their effects on particle size,density and settling velocity          下载免费PDF全文

David C. Barrett  Kyle R. Hodder 《地球表面变化过程与地形》2018,43(10):2232-2242

This study measures the presence of bacteria‐sediment associations (BSAs) in an alpine, glacier‐fed watershed in the Southern Coast Mountains of British Columbia, Canada. The impact of BSAs on the creation of flocculated particles and their settling velocity are quantified using a laser transmissometer. Results from the study indicate that BSAs are present in the watershed and vary over both space and time. The percentage of bacteria associated with sediment particles was found to range from < 1% to 40%. Major sources of planktonic bacteria such as agricultural land and wastewater treatment outflow co‐occur with large decreases in the BSA ratio. Laboratory analysis demonstrates that an increase in the concentration of bacteria was associated with a decrease in the volume concentration of small particles, and a decrease in both estimated density and measured settling velocity for particles in larger size classes; consistent with flocculated particles of increasing complexity arising from combinations of primary particles and/or BSAs. Paleoenvironmental reconstructions using laminated lake sediments in alpine, glacier‐fed systems benefit from a fuller understanding of the geomorphologic processes by which they formed. While bacteria are noted to enhance formation of flocculated particles in laboratory systems, their impact upon geomorphic processes in natural systems have yet to be fully explored. © 2018 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.  相似文献   

Extracting water-related features using reflectance data and principal component analysis of Landsat images     

Boglárka Balázs  Tibor Bíró  Gareth Dyke  Sudhir Kumar Singh 《水文科学杂志》2018,63(2):269-284

This study aimed to map water features using a Landsat image rather than traditional land cover. We involved the original bands, spectral indices and principal components (PCs) of a principal component analysis (PCA) as input data, and performed random forest (RF) and support vector machine (SVM) classification with water, saturated soil and non-water categories. The aim was to compare the efficiency of the results based on various input data. Original bands provided 93% overall accuracy (OA) and bands 4–5–7 were the most informative in this analysis. Except for MNDWI (modified normalized differenced water index, with 98% OA), the performance of all water indices was between 60 and 70% (OA). The PCA-based approach conducted on the original bands resulted in the most accurate identification of all classes (with only 1% error in the case of water bodies). We therefore show that both water bodies and saturated soils can be identified successfully using this approach.  相似文献   

Artificial recharge efficiency assessment by soil water balance and modelling approaches in a multi-layered vadose zone in a dry region     

Mojtaba Pakparvar  Hossein Hashemi  Meisam Rezaei  Wim M. Cornelis  Gholamali Nekooeian  Sayyed Ahang Kowsar 《水文科学杂志》2018,63(8):1183-1202

To assess recharge through floodwater spreading, three wells, approx. 30 m deep, were dug in a 35-year-old basin in southern Iran. Hydraulic parameters of the layers were measured. One well was equipped with pre-calibrated time domain reflectometry (TDR) sensors. The soil moisture was measured continuously before and after events. Rainfall, ponding depth and the duration of the flooding events were also measured. Recharge was assessed by the soil water balance method, and by calibrated (inverse solution) HYDRUS-1D. The results show that the 15 wetting front was interrupted at a layer with fine soil accumulation over a coarse layer at the depth of approx. 4 m. This seemed to occur due to fingering flow. Estimation of recharge by the soil water balance and modelling approaches showed a downward water flux of 55 and 57% of impounded floodwater, respectively.  相似文献   

震后建筑进度BIM估计模型改进   总被引：1，自引：0，他引：1       下载免费PDF全文

武炜  崔邯龙  张丽丽 《地震工程学报》2018,40(4):841-847

传统震后建筑进度BIM估计模型,未考虑精益管理对建筑施工的影响,造成建筑成本浪费较多,影响后期建筑施工进度。本文构建基于BIM和精益管理的震后建筑进度评估模型,根据模型细分震后建筑进度评估过程,在此基础上根据BIM实施三维算量,采用进度计划编制子模型获取各分项工程量,确定建筑施工的主要进度计划,实现对建筑进度计划的编制;通过虚拟施工和现实施工两条主线,利用进度控制子模型实现对施工状态的模拟和精益管理。以此为基础,进行挣值分析比较计划施工成本、实际施工成本和挣值曲线,获取震后建筑的施工进度与成本情况。实验结果说明,本文构建的模型可对震后建筑进度和工程成本进行精准估计,能够减少成本浪费。  相似文献